Your garage door can fail for many reasons.
Most of the problems can be easy to fix.
However, issues that involve garage door springs and cable tension will not be an easy job.
A garage door problem that comes from the cables tends to be more complex.
You will need the proper cable tension in order to make your garage door move without any issues.
When your garage door doesn’t get the right level of tension, it may raise or lower at an incorrect pace which can be dangerous.
Although modern garage doors have enhanced security and protection features, you have to pay extra attention to their heavy-duty components, especially the springs and cables.
These components support the heavy lifting of your garage door, which is why they are on extreme tension.
If your garage door cable gets damaged, it affects the level of tension that your garage door receives.
Learn how to adjust garage door cable tension by going over to this article.
But remember, working with cables that are under tension by yourself involves risks.
Your best takeaway is to let the specialist handle the job for you.
If you think you’re capable of doing it, you can watch this video for some helpful instructions or follow these steps on how to adjust garage door cable tension.
But first, let us discuss the role of your garage door cable.
How Does a Garage Door Cable Works?
You may wonder about the main function of your garage door cable.
This component is typically among the most vital features of your garage door system.
Whenever you lift or close the door, the cable travels further into the torsion springs, simply supporting the overall movement of your garage door.
The resistance spring gives off the lifting power to move the heavy steel door.
It can be under tremendous tension, which can put your safety at risk once it suddenly breaks.
If you’re not careful, you can get serious injuries from it.
On the other hand, the garage door cable serves as protection from spring recoil during a spring failure.
A sudden failure of torsion springs can be devastating and may be lethal.
If a correctly cabled spring breaks, the door will fall to the bottom.
That’s why it is essential to keep the cables in good shape to avoid massive harm and injury from happening.
Adjusting Your Garage Door Cable Tension
If you need to get your garage door cable tension back to the right level, follow these steps for a safe and effective result:
Prepare the Needed Tools
Before you begin, you need to gather all the needed tools and protective gear to adjust your garage door cable tension.
- Safety glasses, gloves, and hard hat
- Solid ladder
- Adjustable wrench
- C clamps and pliers
- Flathead screwdriver
- Wire cutters
Undertake Safety Measures
If your garage door comes with an automatic opener, make sure to disconnect it from the power supply.
This is to avoid any electrical mishaps from happening when taking on how to adjust garage door cable tension.
Also, don’t forget to wear safety gear when doing the job by yourself.
Secure Your Garage Door
Use the remote control to close the door completely.
A slight gap between the pavement and the bottom of the door may indicate that the cables are off the track or uneven.
Shut the door as low as possible.
If you see a slight opening, never try to push it down yourself.
Instead, detach your garage door opener from the drive chain by pulling the cord linked to it.
Loosen the tension of the springs by opening your garage door.
Use your bare hands to lift it open.
Secure the door with c-clamps to make it stay in place and avoid any accidental fall.
Get Your Garage Door Cables in the Correct Position
Disconnect your garage door cable.
You will see one end looped around the rollers while the other one hooked to a lock on the doorway, securing it to the frame.
Look for the frame with holes — this is where you will hook one end of the detached cable to tighten the wire.
You may also have to make necessary adjustments to the cable bracket.
If there’s too much gap, use pliers to remove the bracket, then tighten it by pulling the cables to the frame.
Fasten the wire again to the bracket.
Make sure you don’t loosen the shaft too quickly when tightening the cables, as it may cause it to unwind and twist.
Avoid over tightening the cable and loosening the shaft too much as it can lead to significant complications.
Bring the door down and use metal rods to adjust the spring tension.
Finally, reconnect your garage door to its automatic opener by pulling the cord back.
Test the Door
After all the needed adjustments, test the functionality of your garage door.
Ensure that it’s running smoothly and doesn’t have any problems when opening or closing it automatically.
If you have correctly adjusted the cable and spring tension, you won’t be able to see any gaps at the bottom of your garage door.
If you find the steps on adjusting garage door cable tension daunting and you’re in doubt about how to start the process, don’t stress yourself out.
Consider hiring the expert technicians of Marksman Garage Doors for your safety and convenience.
We can help you make the correct adjustments for your garage door cable tension.
There’s no need to worry as we can back you up 24/7!
Call us if you need our professional garage door service.