How to Install Garage Door Cables

    Neesd a professional technician?

    For garage door services in Pittsburgh and its surroundings, Call us:

    (412) 388-2633

    Or, send a message

    How to Install Garage Door Cables

    The cable is among the power components of your garage door system.

    It mainly supports the opening and closing of the door.

    Without a garage door cable, your door will fail to open and function well.

    The same case happens when this significant component gets damaged.

    When you have a faulty garage door cable, your option is to either get it fixed or replaced.

    If it’s beyond repair, your best solution would be to buy and install a new one.

    But most people don’t know how to install garage door cables properly.

    As a garage door owner, it is important to have ideas on the process in order to assess the extent of work needed for your garage door cable.

    So, here are some helpful tips on how to install garage door cables and the safety measures you need to take into account.

    Safety Precautions

    Before you take action, it is essential to prepare yourself and the tools needed for the work.

    Wear safety gear as necessary to protect yourself from any harm.

    Also, make sure that you are capable of doing a garage door cable replacement and installation.

    Dealing with such extensive work without the right capabilities might lead to injuries and further damages to your garage door system.

    Listed below are the necessary tools you will need for a garage door cable installation:

    • Protective gloves and eyewear
    • Wrenches
    • Vice grip
    • Winding bars
    • Sockets
    • New cables

    Assess Your Garage Door Cable for Replacement

    One important thing you must consider when replacing the cable is its size and the size of your garage door.

    Your needed cable size depends on the type of garage door.

    It’s either you have a garage door that’s standard, vertical, or high-lift.

    If you have a standard-lift residential garage door, you will need a cable size that is 18 inches longer than the height of your door.

    For instance, a 7’ door will need 8’6” cable.

    You have to ensure that you get the right size for the type of door you have in order to make proper replacement and installation.

    Removing Garage Door Cable

    If you’re doing a DIY cable installation, you can follow these instructions when removing your old garage door cable.

    1. Disengage the door by pulling on the emergency release handle.
    2. Hold the garage door open by placing a vice grip underneath the roller on each side of the door.
    3. Unscrew the screws at the center of your garage door. You can insert winding bars for added safety while loosening the tension.
    4. Loosen the screws on the cable drum using a wrench and remove the cables from it.

    Using a socket and ratchet, detach the lag screw near the bottom of your garage door. Then finally, pull the broken cable out of the bracket.

    Installing Your New Garage Door Cable

    After removing your old garage door cable, take the new one and place it on the bottom bracket.

    Then, carefully pull it up to the cable drum at the top on both sides of the door.

    Set the cable properly on the cable drum’s slot.

    Make sure that it doesn’t overlap.

    Wind the new cable onto the drum and then slide the drum into the bearing plate.

    Tighten the cable and the set screws, but don’t over tighten them.

    Use a vice grip on the winding rod while holding the cable, and do this on both sides so that you can increase the tension of the springs with the winding bars.

    After setting the tension, you can now remove the locking pliers and get the job done.

    Testing Your Newly Installed Garage Door Cable

    When you’ve set up everything, it’s time to test if you’ve done the work right.

    Re-engage your garage door and pull down the emergency release handle and then lift it.

    You should notice a click twice, which indicates that it’s in the right position.

    Activate your garage door again by opening and closing it remotely.

    If there are further concerns, it’s best to consult an expert garage door repair technician for your cable installation.

    There are times when only professionals can handle the job.

    When it gets too tough and you’re in doubt, just call a professional garage door technician near you for reliable assistance.

    Hire Marksman Garage Doors for Your New Cable Installation

    Although knowing how to install garage door cables might help you do the job on your own, it may not always give you the best result.

    If you made any errors when replacing your cable or suspect that something else is causing your door to fail, you could always seek professional service from Marksman Garage Doors.

    We can make all necessary cable installation and repairs for you at any time.

    Contact our reliable team right now for bookings and further inquiries.

    Partnership with: garage door repair Miami

    5/5 - (1 vote)

    Recommended articles

    a1 garage door repair service pittsburgh pa, chamberlain garage door opens by itself, clopay garage doors, emergency door services, garage door adjustment do it yourself, garage door bottom roller popped out, garage door cable came off spool, garage door cable repair cost, garage door cable repair kit, garage door cable rubbing on door, garage door cables loose when door is open, garage door installation, garage door installation pittsburgh, garage door lift cables, garage door off track cable, garage door opens sporadically, garage door phantom opening, garage door repair, garage door repair 15237, garage door repair near me, garage door repair pittsburgh, garage door repair south hills pittsburgh, garage door shifted to one side when opening, garage door spring tension chart, garage door tension cable broke, garage door track repair, giel garage doors, henefeld garage doors, how to adjust a garage door that is crooked, how to adjust garage door cables, how to adjust garage door springs and cables, how to adjust garage door to close tighter, how to close garage door with broken cable, how to fix garage door, how to fix up and over garage door cable, how to install garage door springs and cables, how to measure garage door cables, how to put garage door back on track after power outage, how to replace garage door rollers without bending track, how to stop garage door from opening, mcmurray garage doors, merlin garage door opening by itself, pittsburgh garage door sales, steel city garage doors, why garage door opened for no reason
    Contact Us